Can you change the graphics card in a CyberPowerPC? – 2022

gpu

Table of Contents

Making a switch to another graphics card is probably the most efficient option to improve the gaming computer. However it, switching a graphics card isn’t just about buying an updated version. 

It’s also about knowing how to properly insert the component into your motherboard, and making sure that it’s functioning properly. To help you in this, we created this guide.

With new and exciting PC games coming out frequently, it’s possible to notice your old reliable PC not performing to the standards on terms of the Frames per Second department. 

If you’re experiencing screen lag and crashing or even relying on the low or medium settings in order to make a game accessible, these are clear indicators that it’s an ideal time to redesign your system. There is no need to purchase an entire new framework for the chance to play your best games.

Graphics cards may be the most productive tool on your computer, especially when you engage in a lot of gaming. 

Gamers should try to update their graphics cards every couple of years, but you could definitely extend the life of a card more than the time frame. 

Trading in Graphics cards is now simpler in the longer term and driver setup is essentially a hands-off procedure. 

Once you’ve selected your card and you have your computer running and running, you’ll be able to in the majority of cases introduce your new card and ready to use in just two minutes.

Here are the steps on the most effective way to change the Graphics card to your CyberPowerPC gaming computer:

1. Switch off your gaming device

First it is important to turn off your gaming system. Also, try to switch off the switch at the back of your gaming system, located near your Power Supply Unit. After that, disconnect the unit.

2. Remove the sideboard from the body of your case.

Remove the sideboard of the case of your gaming PC. It is possible to do this by loosening the screws at the rear of the unit and then sliding the side board in the reverse direction. The side board case must be removed and place it back on its side.

If you’ve eliminated the sideboard look at the area where you put the graphics card.

3. Examine the space at the top of your PCle.

Your new card for Graphics ought to be able to fit into the PCle space of x16. This opens up to large, level connections located in the lower portion of your motherboard.

 Examine your motherboard first, as there are models with an additional PCl2 x 16 spaces that is able to run at full x16 speed. In any event it is more likely you’ll find that any additional PCle x16 spaces are going to operate at x8 speed, or x4 speed, depending on the type of motherboard.

In this regard, it’s recommended to present your new designs card to the top PCle x16 opening. This is the fastest PCle x16 area on your motherboard and provides you with the most attractive appearance. 

It is also possible to look through the manual of your motherboard to check the precise running speeds of the PCle openings within your motherboard.

Prior to anything else, take out the backplates that compare to the unit. Look in the left-hand side of your PCle’s x16 spaces and remove a part of the thumbscrews keeping the backplates in place. It is essential to perform this in order to maximize your showcase’s yields.

Graphics cards typically require up to two spaces but some are massive and can take up to three. For introducing a component like this take the screws off to allow you to install the larger one. Be sure to put the screws in a secure place, as you’ll need them in order to set up your card for Graphics set up.

Keep in mind that all of the outcomes of your display should be reflected to the rear of your case as you’ll need them to connect the single wire to your display.

4. Insert the Graphics card inside the PCle space of x16

Remove all plastic covers that cover the connector of your graphics card’s PCle and ports for showing. If you’re replacing your previous design card with a fresh and improved version, unplug the show link that is connected to the security clasp on the PCle space. 

Therefore, you should have the option of pulling your old graphics card from the open.

From then on you can place the new images card in the PCle 16×16-sized opening. Make sure that all outputs of your presentation will be visible from the rear of the case. If this is the case then you can push your design cards into the case.

If you have an issue that you are unable to push the design card as far as you can to the edge of your opening you should check to see if there isn’t a wanderer backplate as you would expect.

 If there’s nothing in the way of an opening in the card, offer the card another push to set it up. If it is set correctly it will then be able to return to its place.

5. Remove the cards with designs installed

Find the screws that hold the backplate, because you’ll need them once again in order to set up the design card installed. Install the screws in their respective locations. 

These screws will keep the graphics card from moving, especially when you connect the screen link. 

When you screw your graphics card up it is certain that the card is mounted always on the motherboard.

6. Connect the design card to your power source.

After the design card is properly in place it is time to connect it with your power source. Make sure to check your designs card in the event that it has a 6-pin connector or an 8-pin connector. 

The more elaborate your graphics card is with the more connectors you will find however it is dependent on the manufacturer and model. No matter if it’s an 8-pin or 6-pin connector one, you must have the comparing connection in your power supply box.

Connect the connector to the back of the gaming PC case to ensure that you have space. It will help keep the overall look very neat. This will also help with the flow of wind within your case. 

When connecting your design card with your power source be aware that the connectors are similar to the power connections that connect your motherboard. Do your best to pull down the connectors until they be able to fit correctly.

7. Install and update your showcase driver.

If you’re sure that you’ve connected the graphics card correctly and that it’s working the next thing to do is make sure the correct showcase drivers have been in place. If you’re updating an older NVidia card to a different one, you’ll need to download the most current drivers from their websites.

If, however, you’re updating from an NVidia card to an AMD card, you must remove your current showcase drivers, and start using AMD drivers. To get rid of all driver drivers that are used for momentum you need to open Windows Settings and select Apps to remove the projects.

For AMD drivers all you need to do is to uninstall your AMD Software. For NVidia drivers, you need to remove the associated programs:

  • Nvidia GeForce Experience
  • Nvidia Graphics Driver
  • Nvidia PhysX System Software
  • Nvidia Control Panel
  • Nvidia HD Audio Driver
  • Nvidia USBC Driver

Once all of your old drivers have been removed it is time to restart your gaming computer. Do not be agitated thinking that the game will look different when the framework is started up. This is due to the fact that you’re trying to start introducing the drivers for Graphics first.

When you’ve installed correct software, your gaming system will return to its usual purpose. After that you’ll be able to play games again.

Conclusion

In short, by changing the graphics card in a CyberPowerPC With the latest drivers in place, you can begin putting on your graphic card. Play your most loved game or graphics-intensive software and see what performance you can achieve!

For further information, leave the comments below.

Thank you.

Leave a Comment